[Home ] [Archive]    
:: Main :: About :: Current Issue :: Archive :: Search :: Submit ::
Main Menu
Journal Information::
Editorial Policies::
Articles archive::
For Authors::
Contact us::
Site Facilities::
::
Search in website

Advanced Search
Receive site information
Enter your Email in the following box to receive the site news and information.
Last site contents
:: Contact Us
:: Volume 18, Issue 2 (Foll Text in Persian 2006) ::
J Iran Dent Assoc 2006, 18(2): 8-14 Back to browse issues page
Microtensile bond strength of clearfil SE bond to caries-affected dentin and normal dentin
Amir Ghasemi * 1, Majid Bargrizan , Mina Mahmoodi
1- , aghasemi@icdr.ac.ir
Abstract:   (17502 Views)

Microtensile bond strength of clearfil SE bond to caries-affected dentin and normal dentin

 Dr. A. Ghasemi* - Dr. M. Bargrizan** - Dr. M. Mahmoodi***

 *- Assistant Professor of Operative Dentistry Dept. - Faculty of Dentistry – Shaheed Beheshti University of Medical Sciences.

**- Assistant Professor of Pedodontics Dept. - Faculty of Dentistry – Shaheed Beheshti University of Medical Sciences.

 ***- Dentist.

Background and Aim: Bonding systems have been traditionally used on normal dentin, even though caries-affected and sclerotic dentin are often the clinically relevant bonding substrates. A self-etching primer adhesive system (Clearfil SE Bond) was evaluated for its ability to bond to caries-affected and normal dentin.

Materials and Methods: In this experimental study, twelve extracted human primary molars with occlusal caries were selected. The enamel and superficial dentin were ground with a diamond disk and stained with a caries detector solution (propylen glycol and 1% acid red). The red-stained soft dentin which was classified as infected dentin was excavated and the affected dentin and surrounding normal dentin were polished with a 600 grit silicon carbide paper under running water to achieve a flat surface. The entire flat surface was bonded with Clearfil SE Bond (Kuraray) according to the manufacturer’s instructions and covered with composite resin Clearfil AP-X (Kuraray) to form a composite crown, approximately 4.5 mm high. The teeth were stored in distilled water at room temprature for 24 hours and were then sectioned with a diamond saw under running water in both X and Y directions, perpendicular to the bonded surface with dimensions of approximately 0.8-1 mm, so that the bonded areas of the affected or normal dentin were isolated. The obtained rods were divided into two groups: Affected and sound dentin. After measuring the cross-sectional areas at the interface, the specimens were mounted in a microtensile tester machine and pulled under tension to failure. The mode of failure was evaluated using a streomicroscope and the data were analyzed by t-test.

 Results: Statistical analysis indicated that the microtensile bond strength in affected dentin (21.53±6.52 MPa) was significantly lower (p<0.05) than normal dentin (26.98±7.31 MPa).

Conclusion: The studied self-etch system, attained lower microtensile bond strength in affected dentin as compared to normal dentin.

Key words: Microtensile - Normal dentin – Affected dentin - Primary teeth

Keywords: Microtensile, Normal dentin, Affected dentin, Primary teeth
Full-Text [PDF 161 kb]   (3752 Downloads)    
Type of Study: Research | Subject: General
Send email to the article author

Add your comments about this article
Your username or Email:

CAPTCHA


XML     Print


Download citation:
BibTeX | RIS | EndNote | Medlars | ProCite | Reference Manager | RefWorks
Send citation to:

Ghasemi A, Bargrizan M, Mahmoodi M. Microtensile bond strength of clearfil SE bond to caries-affected dentin and normal dentin. J Iran Dent Assoc 2006; 18 (2) :8-14
URL: http://jida.ir/article-1-47-en.html


Rights and permissions
Creative Commons License This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
Volume 18, Issue 2 (Foll Text in Persian 2006) Back to browse issues page
Journal of Iranian Dental Association

AWT IMAGE

This work is licensed under a Creative Commons Attribution-NonCommercial 3.0 Unported License which allows users to read, copy, distribute and make derivative works for non-commercial purposes from the material, as long as the author of the original work is cited properly

Persian site map - English site map - Created in 0.05 seconds with 37 queries by YEKTAWEB 4645